New silent screw air compressor

A SILVER air compressor is a silent encapsulated rotary screw compressor designed for performance and reliability. The FIAC silver air compressor model comes equipped with a TEFC high-efficiency electric motor, WYE Delta Starter, Sound attenuating enclosure, FIAC easy control microprocessor. . FIACquiet rotary screw air compressorsare available in a wide variety of models, which range from 3-50 HP. The FIAC Silver air compressors are easy to. . There are many benefits to choosing a base mounted quiet screw rotary compressor. The screw unit has low running speeds and high efficiency, and this results. . Werther provides the SILVER air compressors to small producers, big industry, and all sizes in between. Each industry has very different needs and applications for these products. Some of the common industries we serve include: 1. Laboratory 2. Medical 3. Electronic 4. Food & Beverage 5. Dental Latest generation compressor screw technology with fully integrated aluminum block and direct drive transmission, maximum pressure up to 10 bar, compact and portable for easy mobility, low noise and vibration for close point of use (POU) and minimum piping, plug-and-play operation with no expertise required and high efficient direct transmission contributes to high reliability and easy maintenance. [pdf]

Screw air compressor factory inspection standards

1-1 Scope of Application This document covers procedures and methods of tests, examinations and inspections to be performed to the Screw Compressor which has been manufactured and supplied by screw compressor vendors. 1-2 Purpose of Examination and lnspection The purpose of the examinations. . 2-1Genaeral General descriptionon examinations/inspections to be performed on the compressor proper and the relatedparts are mentioned in this chapter. The inspection itemsof each major part are shown in inspection and test plan. 2-2Material Inspection. . After completion of the test, the rotors and the rotor chamber will be visually inspected through the discharge nozzle. (The discharge side is under most severe conditions, and the visual inspection of the discharge side is a normal practice to check a rotor. . Following Items are measured in Heat Run, Mechanical Run and Performance Test: 1. Atmospheric Pressure 2. Atmospheric Temperature 3. Relative Humidity (Only in Performance Test) 4. Inlet Pressure 5. Inlet Temperature 6. Discharge Pressure. . Following componenets are used for test from Shop Facilities: 1. Driver( Motor) 2. Couplings 3. Baseplate 4. Suction Filter 5. Suction Silencer 6. Discharge Silencer 7. Lube Seal Oail Unit (Include Oil Reservoir) 8. Piping 9. Instruments 10. Thrust Bearing T em perature. [pdf]

FAQS about Screw air compressor factory inspection standards

What does observed mean in a screw compressor inspection?

The term observed means that the purchaser requires notification of the timing of the inspection or test. The screw compressor testing or inspection is performed as scheduled, however, if the purchaser or his agent is not present the vendor can proceed to the next step.

Why do you need a screw compressor inspection?

As one of the most widely used air compressor models on the market, screw compressors are in high demand. With tight tolerances, these parts require an inspection solution that delivers both high accuracy and the fastest possible scanning speeds for maximised throughput.

What are the safety standards for air compressors for process industries?

These are covered by ASME B19.3, Safety Standard for Compressors for Process Industries. The principles promoting safe generation and use of compressed air are not restricted to new air compressor systems. It is recommended that all air compressor systems be reviewed to consider possible changes due to revision of this Standard.

What are the inspection requirements for air compressor / receiver?

As can be seen below, the inspection requirements refer back to AS3788:2006, where Table 4.1 gives the periodic inspection requirements. If the air compressor / receiver has a PV (design pressure in MPa x volume in L) value below 150 MPaL does not require period external and internal inspections.

Who conducts inspections & inspections of screw compressors?

1-3-2 The examinations and inspections shall principally be carried out by the staffs of the quality control and assurance of screw compressor manufacture, and may be, if required, witnessed or observed by Purchaser, Client or appointed third-party inspection agent.

What is the temperature limit for a screw compressor?

Standard screw compressor package design based on IIAR/mechanical code equipment room limits of 104°F (40°C). Screw package high temperature limit based on WEG motor. Other motor ratings are available for special applications. Screw package low temperature limit based on oil temperature limits.

Heavy down-the-hole drilling rig drilling

A down-the-hole drill, usually called DTH by most professionals, is basically a jackhammer screwed on the bottom of a drill string. The fast hammer action breaks hard rock into small cuttings and dust that are evacuated by a fluid (air, water or drilling mud). The DTH hammer is one of the fastest ways to drill hard rock. The system is thought to have been invented independently by Stenuick. Origin of the nameDTH is short for “down-the-hole”. Since the DTH method was originally developed to drill large-diameter holes downwards in surface-drilling applications, its name originated from the fact that the percussion mechanis. . In DTH drilling, the percussion mechanism – commonly called the hammer – is located directly above the drill bit. The drill pipes transmit the necessary feed force and rotation to the hammer and the bit, along with the flui. . A is first thought to have been used for rock drilling in 1844. Many quarries used hand held tools that required the driller to suspend himself from a rope over the quarry face in order to place the drill hole in. [pdf]