FACTORY DIRECT 7.5 KW SCREW COMPRESSOR INDUSTRIAL SCREW AIR
Screw air compressor factory inspection standards
1-1 Scope of Application This document covers procedures and methods of tests, examinations and inspections to be performed to the Screw Compressor which has been manufactured and supplied by screw compressor vendors. 1-2 Purpose of Examination and lnspection The purpose of the examinations. . 2-1Genaeral General descriptionon examinations/inspections to be performed on the compressor proper and the relatedparts are mentioned in this chapter. The inspection itemsof each major part are shown in inspection and test plan. 2-2Material Inspection. . After completion of the test, the rotors and the rotor chamber will be visually inspected through the discharge nozzle. (The discharge side is under most severe conditions, and the visual inspection of the discharge side is a normal practice to check a rotor. . Following Items are measured in Heat Run, Mechanical Run and Performance Test: 1. Atmospheric Pressure 2. Atmospheric Temperature 3. Relative Humidity (Only in Performance Test) 4. Inlet Pressure 5. Inlet Temperature 6. Discharge Pressure. . Following componenets are used for test from Shop Facilities: 1. Driver( Motor) 2. Couplings 3. Baseplate 4. Suction Filter 5. Suction Silencer 6. Discharge Silencer 7. Lube Seal Oail Unit (Include Oil Reservoir) 8. Piping 9. Instruments 10. Thrust Bearing T em perature. [pdf]FAQS about Screw air compressor factory inspection standards
What does observed mean in a screw compressor inspection?
The term observed means that the purchaser requires notification of the timing of the inspection or test. The screw compressor testing or inspection is performed as scheduled, however, if the purchaser or his agent is not present the vendor can proceed to the next step.
Why do you need a screw compressor inspection?
As one of the most widely used air compressor models on the market, screw compressors are in high demand. With tight tolerances, these parts require an inspection solution that delivers both high accuracy and the fastest possible scanning speeds for maximised throughput.
What are the safety standards for air compressors for process industries?
These are covered by ASME B19.3, Safety Standard for Compressors for Process Industries. The principles promoting safe generation and use of compressed air are not restricted to new air compressor systems. It is recommended that all air compressor systems be reviewed to consider possible changes due to revision of this Standard.
What are the inspection requirements for air compressor / receiver?
As can be seen below, the inspection requirements refer back to AS3788:2006, where Table 4.1 gives the periodic inspection requirements. If the air compressor / receiver has a PV (design pressure in MPa x volume in L) value below 150 MPaL does not require period external and internal inspections.
Who conducts inspections & inspections of screw compressors?
1-3-2 The examinations and inspections shall principally be carried out by the staffs of the quality control and assurance of screw compressor manufacture, and may be, if required, witnessed or observed by Purchaser, Client or appointed third-party inspection agent.
What is the temperature limit for a screw compressor?
Standard screw compressor package design based on IIAR/mechanical code equipment room limits of 104°F (40°C). Screw package high temperature limit based on WEG motor. Other motor ratings are available for special applications. Screw package low temperature limit based on oil temperature limits.
Egypt Viken Screw Air Compressor Agent
Address: 16-3 رقم 6، 6th of October City (2), Giza Governorate 12451, Egypt Phone:+201221641594 Plus code:WVCJ+96 6th of October City (2), Egypt Product: 1. Portable compressors 2. power generators 3. pumps and tools 4. Vacuum Pumps 5. oil filter . Address:1 Street 273, El-Basatin Sharkeya, El Basatin, Cairo Governorate, Egypt Phone:+20227545076 Plus code:X7HH+G4 El Basatin, Egypt Product: 1. air oil separator, 2.. . Address:El Nasr Rd، DAHAR، Hurghada 2, Red Sea Governorate, Egypt Phone: +20653552747 Plus code:6RWF+HJ Hurghada 2, Egypt Product: 1. centrifugal air compressors 2. PET compressed air solutions 3. Lubrication Equipment BAUER. . Address:N83 Al Sabtiah, Boulaq Num.1, Bulaq, Cairo Governorate, Egypt Phone:+20225774400 Plus code:368P+76 Bulaq, Egypt. . Address:كم 28, Cairo – Alexandria Desert Rd, Abou Rawash, Giza Governorate 12677, Egypt Phone:+20235391987 Plus code: 326M+44 Abou Rawash, Imbaba, Egypt Product: 1. condensing units 2. BSB & BSD 3. BSV 4. BMP 5. Industrial Air Compressor 6. rotary. [pdf]